Other

The Problem Solvers Cassette Spacers are made of light and durable anodized aluminum and come in different thicknesses for correctly spacing various brand and model cassette cogs. Measure and match your spacers to choose the right width.

The Problem Solvers Handlebar Clamp Shim allows you to fit almost any handlebars in almost any stem. It's machined of light and durable aluminum and grooved on the inside to hold tightly.

Shimano's In-Line Brake Cable Adjuster with quick release allows you to make changes to your road caliper brake's cable tension or open a brake caliper's arms to remove a wheel.

A well-exercised dog is a happy dog, so give Fido a good workout while you ride! Sunlite's Dog Leash consists of a metal bar that mounts under the rear axle bolt or quick-release and straps to your chainstay. This keeps the center of gravity low so you stay stable if your dog pulls to one side. The bar is long enough to keep your pup away from the bike, too.

The Problem Solvers Cable Doublers are made of light, durable machined and anodized aluminum and they are Teflon coated for a super-smooth cable pull every time. They come in two models. The first allows you to control two brakes with one lever. The second allows you to control one brake with two levers. Why? Well, there are myriad applications: tandems, cyclocross bikes, fixies, tricycles, recumbents, cycles for those with special needs, bike polo bicycles, those 4-person bikes you see on beach boulevards, and so on. You could even link both models of Cable Doublers together for the ultimate in redundancy!

When you need to move your handlebars up, install Sunlite's Chromoly Quill Stem Extender. One end goes inside the steerer tube and your quill stem inserts into the top. It provides 8 1/4 inches of rise and is compatible only with quill stems and steerer tubes.

Dimension Seatpost Clamps - Diameters: 28.6mm, 30.0mm, 31.8mm, 35.0mm - Weight: 34g

Dimension Steerer Extender adds 2 to 3-1/4" height to steerer. - Extender clamps to steerer; stem clamps to extender - Adds 2 to 3-1/4-inch height to threadless steerer - Includes top cap and long bolt - 40mm of threadless steerer is required for proper installation - Do not stack steerer extenders; no more than one steerer extender recommended per bike - WARNING: Dimension Steerer Extender is not recommended for use on forks with carbon fiber steerers

We won't blame you for attention to detail. In fact, Spank's got your back. These headset spacer kits are available in 8 popular colors, and come with 3 rings in incremental sizes, to make your next cockpit set up a thing of ease and beauty. - Material: Alloy - Sizes (mm): 3 / 6 / 12 - Diameter: 1 1/8" (28.6mm) - Finish: Brushed Anodized

- Ahead Stem Shim allows the use of 1-1/8 stem on 1" steerer tube - 28.6mm/25.4mm

All Wheels Manufacturing replacement derailleur hangers are produced in their Colorado shop to exacting tolerances. - CNC machined 6061 aluminum - Black anodized finish - (2) M4x14 socket head screws included - Replaces Diamondback Part # 32-68-004

Lip-Locks don’t just secure your seatpost. They do it while looking good! Add a little functional bling to your ride. Available in a variety of sizes and color choices. - Non-quick-release version of the Flip-Lock - Stainless steel pivot and bolt - Black, Silver, Blue, Green, Red, and Pink anodized with laser-etched logo - Black = 28.6, 30.0, 30.6, 32.0, 35.0 and 36.4mm - Silver, Blue, Green, Red, Gold, and Pink = 30.0, 30.6, 32.0 -and 35.0mm - Orange, Purple, and Lime = 30.0, 32.0, and 35.0mm - 34g

Shimano Di2 External Battery Mounts - All Di2 components on the bicycle require the same firmware version. Using Di2 components with different firmware versions may cause malfunctions - Use Di2 system checker to update component firmware

Shimano Di2 External Battery Mount - All Di2 components on the bicycle require the same firmware version. Using Di2 components with different firmware versions may cause malfunctions - Use Di2 system checker to update component firmware

Original equipment rear derailleur pulleys and inner cage for SRAM X01 Eagle rear derailleurs.

SRAM eTap batteries are literally a snap to remove and charge. Just flip the tool-free battery latch up and slide the battery up and out of the derailleur. Then snap the battery into the USB powered charger and connect the charger to any USB power source or A/C USB adaptor. A full charge takes up to 60 minutes to complete.The eTAP Powerpack includes a battery charger, cord, transmitter, and international adaptors (US/EU/GB).

Zipp Speed Weaponry Vuka Aero Center Cap Kit - Bolt kit sold separately

Thomson Faceplates are compatible only with Thomson stems. Compatible only with X4 stems

The Vuka Clip On is all about providing the ultimate in fit, security, and adjustability for you to be faster and more efficient in your triathlon or time-trial aero position. Offered in high-performance carbon fiber, in both above and below-bar configurations. Additional risers, armrests and aero accessories available for fine tuning and maintenance. - Diameter: 31.8 - EVO 70/110: Weight: 480g, Length: 360mm - Race: Weight: 480g, Length: 330mm

- Includes 61803 bearings and one grease syringe - Measurable wattage savings between 1.5 and 9 watts per bearing set, depending on the level and condition of your existing bearings - Note: 88 front and 188v9 rear hubs are on all 2014 and newer Zipp 202, 303, 404, 808 - One kit required for: Zipp 88, 30 and 60 front hubs Zipp 188v8 rear hubs Zipp ALL free hub driver bodies - These 61803 bearings are not interchangable with the 77/177 hub 61803 bearings

The tool-free Maxle Ultimate Rear brings exceptional stiffness and durability to your ride in a high clamping force, easiest-to-use internal cam thru axle system.

Wolf Tooth designed these bolts to be the best on the market. These optimized single chainring bolts have a 4mm hex socket on the bolt and a 6mm hex socket on the nut...that's right, no more spanner for your single ring bolts! These are 6mm long so they work perfectly with any bolt on single chainring that does not have threaded standoffs. - 6mm length - Made in the US out of 7075 Aluminum Alloy - Has hex heads on both the bolt and nut for easy installation - Max torque of 6-7 Nm with light grease on threads only

Replace your old aerobar armrest pads and upgrade to the comfort of Fizik's TechNoGel Tri Pads. Made from Fizik's shock-absorbing Technogel, these cut-to-fit pads make every second in the aero position easier and more comfortable. Plus, the pads are easily removed for cleaning.

All Wheels Manufacturing replacement derailleur hangers are produced in their Colorado shop to exacting tolerances. - CNC machined 6061 aluminum - Black anodized finish - Includes (1) M8 Chainring Bolt

All Wheels Manufacturing replacement derailleur hangers are produced in their Colorado shop to exacting tolerances. - CNC machined 6061 aluminum - Black anodized finish - Includes (1) M8 Chainring Bolt

All Wheels Manufacturing replacement derailleur hangers are produced in their Colorado shop to exacting tolerances. - CNC machined 6061 aluminum - Black anodized finish - Includes (2) M4x8 Flat Head Screws

All Wheels Manufacturing replacement derailleur hangers are produced in their Colorado shop to exacting tolerances. - CNC machined 6061 aluminum - Black anodized finish - Includes (2) M3x10 Flat Head Screws

All Wheels Manufacturing replacement derailleur hangers are produced in their Colorado shop to exacting tolerances. - CNC machined 6061 aluminum - Black anodized finish - Includes (1) M8 Chainring Bolt

All Wheels Manufacturing replacement derailleur hangers are produced in their Colorado shop to exacting tolerances. - CNC machined 6061 aluminum - Black anodized finish - Includes (2) M3x10 Flat Head Screws

All Wheels Manufacturing replacement derailleur hangers are produced in their Colorado shop to exacting tolerances. - CNC machined 6061 aluminum - Black anodized finish - Includes (2) M3x10 Socket Head Cap Screws